Resource Lesson
Kirchhoff's Laws: Analyzing Circuits with Two or More Batteries
Printer Friendly Version
The simple rules used for analyzing networks with only one battery and a collection of resistors do not work as well when you introduce one or more additional batteries. The difficulty arises in trying to determine which batteries are powering the circuit, or discharging, and which one are charging.
Consider the following example,
Is
ε
_{1}
, the battery on the line between A and D, charging or discharging? What about
ε
_{2}
, the battery between B and E? There is no easily apparent way to be certain until the circuit is tested and analyzed. To do this analysis we will use Kirchhoff's Rules.
Junction Rule
Kirchhoff's first rule states that the sum of the currents coming into a junction equals the sum of the currents going out of a junction.
This is a statement of conservation of charge (1 amp = 1 coulomb/sec) in a circuit.
In our circuit diagram shown above, B and E are junctions while points A, C, D, and F are merely "corners" labeled to assist us in our discussion.
Even though you may arbitrarily assign directions to the currents, the general rule is to draw currents "coming out" of the positive terminal of a battery. Later, if your choice of direction later turns out to be incorrect, the value of I will simply be negative. However, you must LEAVE it alone since a change of SIGN will result in incorrect values for V and R as you continue to analyze these remaining properties of your circuit.
In the diagram shown above,
the current called I
_{1}
runs counterclockwise from B to E through corners A and D,
the current called I
_{2}
runs clockwise from E to B through corners C anf F, while
the current called I
_{3}
ONLY runs clockwise from E to B.
Remember that currents flow around corners (A, C, D, F) in a circuit but divide when they come to junctions (B, E) which denote parallel configurations.
At
junction B
, the only current "coming in" is I
_{2}
while the currents called I
_{1}
and I
_{3}
are "going out." We would write the Kirchhoff's junction equation as:
Notice at
junction E
that the currents called I
_{1}
and I
_{3}
are "coming in" while the only current "going out" is I
_{2}
.
Junctions B and E reflections of each other since they produce identical equations.
Loop Rule
Kirchhoff's second rule states that the sum of the voltage changes around a closed path, or loop, in the circuit must add to zero.
This is a statement of conservation of energy (1 volt = 1 J/C) in a circuit.
In our circuit, there are three loops
A
BCFED
A
 the perimeter
A
BED
A
 the left side
C
FEB
C
 the right side
Notice that each loop should begin and end at the same position in the circuit to be considered closed.
The rules for assigning SIGNS to the
voltage changes across a resistor
in a closed loop for Kirchhoff's loop rule are:
V = IR if the direction of the current agrees with the direction of the loop.
Conversely, V = +IR if the direction of the current opposes the direction of the loop.
The rules for assigning SIGNS to the
voltage changes across a battery
in a closed loop for Kirchoff’s loop rule are:
V = 
ε
if the direction of the loop crosses a battery from + to  (high to low )
V = +
ε
if the direction of the loop crosses a battery from  to + (low to high)
Kirchoff’s loop rule is often used to determine the correct orientation of batteries in circuits which have more than one battery  that is, which battery or batteries are discharging and which one(s) might be charging.
Let's look at the first loop,
A
BCFED
A
, which goes around the perimeter of the circuit.
Starting at A, we encounter no circuit elements until we reach C where the loop will next pass over resistors R
_{2}
and R
_{3}
in the same direction as the current I
_{3}
. After reaching point F we do not encounter any more circuit elements again until we reach D where we cross the battery 1 from "high to low" (+ to ) and then resistor R
_{1}
in the opposite direction as the current I
_{1}
. After which we return to A, our starting point.
I
_{3}
R
_{2}
 I
_{3}
R
_{3}

ε
_{1}
+ I
_{1}
R
_{1}
= 0
Now let's look at the second loop
A
BED
A
which circles the left side of the circuit.
Starting at A, we encounter no circuit elements until we reach the positive terminal of the battery,
ε
_{2}
. Here the loop will cross the battery 2 from "high to low" (+ to ). After reaching E we do not encounter any circuit elements until after we pass D where the loop initially crosses the battery 1 from "high to low" (+ to ) and then crosses the resistor R
_{1}
in the opposite direction as the current I
_{1}
. We then return to A, our starting point.

ε
_{2}

ε
_{1}
+ I
_{1}
R
_{1}
= 0
Now let's look at the third loop
C
FEB
C
which circles the right side of the circuit.
Starting at C the loop will first pass over resistors R
_{2}
and R
_{3}
in the same direction as the current I
_{3}
. After reaching point F we do not encounter any more circuit elements again until we reach E where the loop will then cross the battery 2 from "low to high" ( to +) before returning to B and then C, our starting point.
I
_{3}
R
_{2}
 I
_{3}
R
_{3}
+
ε
_{2}
= 0
Now let's put in some values for the batteries and the resistors to determine each of the unknown currents and answer our original questions of which battery (or batteries) is discharging and which are charging.
Let's set each resistor equal to 10 Ω, battery 1 equal to 9V, and battery 2 equal to 6V.
A
BCFED
A:
I
_{3}
R
_{2}
 I
_{3}
R
_{3}

ε
_{1}
+ I
_{1}
R
_{1}
= 0
 I
_{3}
(10)  I
_{3}
(10)  9 + I
_{1}
(10) = 0
 I
_{3}
(20) + I
_{1}
(10)  9 = 0
 2I
_{3}
+ I
_{1}
= 0.9
A
BED
A:

ε
_{2}

ε
_{1}
+ I
_{1}
R
_{1}
= 0
 6  9 + I
_{1}
(10) = 0
10I
_{1}
= 15
I
_{1}
= 1.5 A
C
FEB
C:
I
_{3}
R
_{2}
 I
_{3}
R
_{3}
+
ε
_{2}
= 0
Since all three current values are positive:
1. we made the correct choice for each direction
2. we know that both batteries are discharging
 I
_{3}
(10)  I
_{3}
(10) + 6 = 0
 20I
_{3}
= 6
I
_{3}
= 0.3 A
Junction B:
I
_{2}
= I
_{1}
+ I
_{3}
I
_{2}
= 1.5 + 0.3
I
_{2}
= 1.8 A
Check:
 2I
_{3}
+ I
_{1}
= 0.9
 2(0.3) + 1.5 = 0.9
 0.6 + 1.5 = 0.9 yes!
Related Documents
Lab:
CP 
Series and Parallel Circuits
Labs 
Parallel and Series Circuits
Labs 
RC Time Constants
Labs 
Resistance and Resistivity
Labs 
Resistance, Gauge, and Resistivity of Copper Wires
Labs 
Telegraph Project
Labs 
Terminal Voltage of a Lantern Battery
Labs 
Wheatstone Bridge
Resource Lesson:
RL 
A Comparison of RC and RL Circuits
RL 
Ampere's Law
RL 
An Introduction to DC Circuits
RL 
Capacitors and Dielectrics
RL 
Dielectrics: Beyond the Fundamentals
RL 
Electricity and Magnetism Background
RL 
Filaments
RL 
Kirchhoff's Laws: Analyzing DC Circuits with Capacitors
RL 
Magnetic Field Along the Axis of a Current Loop
RL 
Magnetism: CurrentCarrying Wires
RL 
Meters: CurrentCarrying Coils
RL 
Parallel Plate Capacitors
RL 
RC Time Constants
RL 
Torque on a CurrentCarrying Loop
Worksheet:
APP 
The Circuit Rider
APP 
The Cycle Shop
CP 
DC Currents
CP 
Electric Power
CP 
Ohm's Law
CP 
Parallel Circuits
CP 
Power Production
CP 
Power Transmission
CP 
RIVP Charts #1
CP 
RIVP Charts #2
CP 
Series Circuits
NT 
Brightness
NT 
Light and Heat
NT 
Parallel Circuit
NT 
Series Circuits
NT 
Shock!
WS 
Capacitors  Connected/Disconnected Batteries
WS 
Combinations of Capacitors
WS 
Introduction to R  I  V  P Charts
WS 
Kirchhoff's Laws: DC Circuits with Capacitors
WS 
Kirchhoff's Laws: Sample Circuit
WS 
Resistance, Wattage, and Brightness
TB 
34A: Electric Current
TB 
35A: Series and Parallel
TB 
Advanced Capacitors
TB 
Basic Capacitors
TB 
Basic DC Circuits
TB 
MultipleBattery Circuits
TB 
Textbook Set #6: Circuits with Multiple Batteries
PhysicsLAB
Copyright © 19972024
Catharine H. Colwell
All rights reserved.
Application Programmer
Mark Acton